If you've spent any time in photo booth Facebook groups, you've seen it happen. Someone posts a printer problem: a ribbon error, a jam, a printer that won't beep when you load paper, or a blinking red light in the middle of a wedding. Within the hour, Bill Vahrenkamp has shown up in the comments with the fix.
Bill has been using and supporting dye-sub printers for more than 30 years, he's taken DNP's repair training, and he's an admin of the DNP Users & Support group. He's also spoken on printing at Photo Booth Expo, Imaging USA and Texas PPA's I Heart Photography. In 2023 he was inducted into the Photo Booth Hall of Fame, and fellow inductee Rex Huang summed up why: Bill has helped thousands of booth owners with printer and media problems without asking for anything in return.
I went back through his posts and comments across the photo booth groups (Photo Booth Community, Photo Booth Network, DNP Users & Support, Photo Booth Business Owners, The Photo Booth Collab, Darkroom Booth User Network, Booth.Events Community and more) and pulled together the advice he gives most often. Bill, thank you. This community is better because of you.
1. Take the media out before you transport the printer
This is the one Bill repeats most, and he's had to defend it many times. Someone always replies that they've left the paper and ribbon in for years with no problems. His answer is always the same:
"Transporting your printer with paper and ribbon in the printer is like being in a vehicle without a seatbelt. It's fine until it's not."
Bill Vahrenkamp
He also points out that this rule doesn't come from him. It comes from the companies that make the printers:
"All dyesub manufacturers have always said to transport printers without media in the printer and dump the shards. They should know, it's their printers."
Bill Vahrenkamp
Why it matters: Vibration from the drive is the problem, however well the printer is padded. According to Bill:
- The ribbon can bang into the print head and damage the head or the head frame. That causes paper jams and ribbon snaps.
- The paper wound through the printer can knock the paper load sensor out of place. Then the printer won't beep when the paper is in far enough.
- When a booth owner calls with a jam, a snapped ribbon or a printer that won't load, his first question is whether they transport with media in. He says the answer is almost always yes.
How Bill packs for an event:
- Put the media back in its original packaging. If you've lost the ribbon packaging, a gallon zip-top bag works. You can also leave the ribbon in its tray and put the tray in a bag or a small plastic tub.
- Dump the shards (the cut-off trim) every time.
- On the DNP RX1HS, put in the foam print-head pad. Every RX1HS comes with one, and DNP says it's required for transport. The front door should still close with the pad in, without tape.
- Carry the printer the same way up that it prints. Don't stand it on its face.
- On the RX1HS, if you don't want to fully unload the paper, you can leave it in as long as you back the paper out so it isn't sitting on the load sensor. The ribbon still has to come out.
- For cases, Bill uses Pelican 1610 hard cases for DNP DS620s. For the plastic 4x6 print tray on the DS40, he suggests a plastic container so it doesn't snap. The 620 and RX1HS trays fold up.
2. Choosing a printer: the Lexus, the Highlander and the Corolla
"Which printer should I buy?" gets asked every week. Bill answers with the same car comparison every time, and it's the clearest explanation I've seen:
"Think of the DNP 620 as the Lexus and the RX1HS as a Toyota Highlander and QW410 the Corolla."
Bill Vahrenkamp
| Printer | Bill's take |
|---|---|
| DNP DS620A ("the Lexus") | Fastest, best quality, most media options (including metallic and fine matte), and the most expensive. Bill's own team runs four of them. |
| DNP DS-RX1HS ("the Highlander") | A good printer. It's slower than the 620 but holds more media. There's also a 6x8 kit for it. |
| DNP QW410 ("the Corolla") | Slowest, smallest and cheapest. Its media costs more, it holds the least, and it doesn't cut 2-2x6 strips, so for strips you use its pricier 2x6 perforated media. Because the paper runs vertically, it can cut 4x4. |
His bottom line: "Look at your needs and budget and buy accordingly." He also warns to buy from an authorized DNP dealer (Amazon isn't one) so your warranty is honored. A printer that fails under warranty isn't wasted money if you have a dealer invoice. Call DNP.
Other printer notes from Bill:
- Square prints: On the 620, cut a 4x6 or use the R2 perforated media (4x4/2x4). 5x7 media can cut 5x5.
- Panoramic prints: The 620 also prints 6x14 and 6x20 panoramics.
- Big prints: The DNP DS820 prints 8x8 up to 8x32. The Fujifilm DX100 (replaced by the DX400W) prints any length from 3.5" up to 39". Bill started a Fujifilm DX400W user group when he couldn't find one.
- JoySpace U826 / SwiftFoto (HiTi): Based on the HiTi 525 platform. Media options include regular, holographic, metallic, sticker and translucent. The metallic is very shiny and looks great in black and white.
- Epson SureLab D1070: Similar to the Fujifilm DX400W. A six-color inkjet that prints 3.5" to 39" long on 4", 5", 6" and 8" wide paper. (Not to be confused with Epson's D570, which is a printer for transfers.)
3. Update your firmware
After "Did you transport it with media in?", Bill's next question is almost always "Have you updated your firmware?"
"Newest Firmware never hurts to have."
Bill Vahrenkamp
- New DS620 media needs new firmware. The newer 620 media (wrapped in paper, in a smaller box) can refuse to load on old firmware. The classic case: you run out of old media mid-event, load a new roll, and the printer won't start. Bill calls firmware "the OS of the printer."
- Updating 620 firmware: take the ribbon out when updating from Windows, but leave it in when updating from a Mac.
- Drivers don't install firmware. They're separate downloads. Keep the newest driver on your computer too, because new drivers don't always work with old firmware.
- Check what you have with DNP's free PrinterInfo tool. It shows the firmware version and print count, and you'll find it on DNP's downloads page too.
- Running several printers? Unlike the RX1-to-RX1HS upgrade, updating the 620 to firmware 4.52 doesn't stop your old media from working, so you can update any time. Bill has, with no issues.
- Get firmware and drivers from DNP's downloads page.
4. Bill's troubleshooting checklist
When a printer acts up, Bill works through the likely causes in order. In one thread he said feeding issues come down to one of four things:
- Bad media. Try another roll.
- Bad power. Does it happen at more than one venue?
- Weather. Cold is the one to watch: a cold ribbon can snap. Let it warm up at room temperature for 30 minutes and it will be fine. You'll often read that humidity makes the ribbon stick, but Bill lives in Texas, has never had that issue, and has never heard a tech person mention it.
- Mechanical issues. This brings it back to transporting with media in and not dumping the shards.
The reset he recommends for ribbon errors and "won't go to ready": Unplug the USB and leave it unplugged. Remove the paper and ribbon. Turn the printer off, then back on. Reload the paper and ribbon. Check whether the printer cuts its alignment sheets and goes to ready. Booth owners have fixed stubborn ribbon errors this way, and some could only update firmware afterward.
Missing color bands, ribbon tears, weird errors at certain venues: Suspect the power. Bill recommends a UPS battery backup (his team uses APC and CyberPower; spend $100 or more) for outdoor events, old buildings and venues with known power issues.
Driver weirdness (settings that won't save, "write failure", orientation or cut settings reverting): First find out where the problem is. Test print from the driver on Windows, or from Preview on a Mac. If that print works, the problem is your software or print server, not the printer.
If it doesn't print, you may need to reinstall the driver. Unplug the USB and reinstall the driver, plug the USB back in, and then test print again from the Windows driver or Preview on the Mac.
If the test print still doesn't work, now uninstall the driver, reinstall it again, and then test print from the driver or Preview.
If it still fails, it's time to call the manufacturer's tech support.
Lines on prints or muddy prints: Clean it. Use lint-free alcohol wipes on the internal surfaces, then a fresh wipe on the print head, the platen roller and every metal roller, spinning them as you go. For stubborn lines, use the DNP head cleaning kit, which works on all dye-sub heads. One booth owner cleared a persistent cyan line by repeating Bill's cleaning-pen routine from his YouTube video several times.
5. Color: don't overthink it
People love to tweak ICC/ICM profiles and color settings. Bill's advice is short:
"Don't overthink it."
Bill Vahrenkamp
Calibrate your screen. If prints look darker than your screen, he says to trust your prints and fix your exposure and screen, not the printer.
Thank you, Bill
A lot of booth owners have saved an event because Bill answered a frantic post at the right moment. As one owner put it after Bill's firmware tip fixed a printer mid-rental, he "saved my butt." He shares this freely, year after year, and the photo booth industry is better for it.
Next time you pack up after an event, take the ribbon out, bag the paper and dump the shards. It's fine until it's not.
Where to buy printers and media
For all your printer needs (printers, media, parts and advice), I recommend Ruben Gama at Foto Club Inc. Tell him I sent you.
Steven Murphy, Murphy's Memories Interactive Photography
As an Amazon Associate I earn from qualifying purchases.
